http://www.tracopower.com features ultra wide 4:1 input voltage range single output voltage models from 1.8 to 15 vdc dual output voltage models extended operating temperature range: C40c to 85c under voltage lockout remote on/off shielded metal case with insulated baseplate optional heatsink lead free design - rohs compliant 3-year product warranty dc/dc converters ten 30wi series, 30 watt the ten 30wi series is a family of high performance 30w dc-dc converters fea - turing ultra wide 4:1 input voltage ranges in a compact low profle package with industry-standard footprint. a very high effciency allows operating temperatures up to 85c. a built-in flter for both input and output minimizes the need for external fltering. further standard features include remote on/off, output voltage trimming, over voltage protection, under voltage lockout and short circuit protection. typical applications for these products are battery operated equipment and distrib - uted power architectures in communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required and space is limited on the pcb. order code input voltage range output voltage output current max. effciency typ. ten 30-2408wi 1.8 vdc 8000 ma 80 % ten 30-2409wi 2.5 vdc 8000 ma 85 % ten 30-2410wi 3.3 vdc 6000 ma 87 % ten 30-2411wi 10 C 40 vdc 5.0 vdc 6000 ma 87 % ten 30-2412wi (nominal 24 vdc) 12 vdc 2500 ma 87 % ten 30-2413wi 15 vdc 2000 ma 88 % ten 30-2422wi 12 vdc 1250 ma 85 % ten 30-2423wi 15 vdc 1000 ma 86 % ten 30-4808wi 1.8 vdc 8000 ma 81 % ten 30-4809wi 2.5 vdc 8000 ma 86 % ten 30-4810wi 3.3 vdc 6000 ma 87 % ten 30-4811wi 18 C 75 vdc 5.0 vdc 6000 ma 88 % ten 30-4812wi (nominal 48 vdc) 12 vdc 2500 ma 87 % ten 30-4813wi 15 vdc 2000 ma 88 % ten 30-4822wi 12 vdc 1250 ma 86 % ten 30-4823wi 15 vdc 1000 ma 87 % models page 1 of 4
http://www.tracopower.com input specifications input current at no load 1.8 vout models: 35 / 20 ma typ. (nominal input 24/48 vin) 2.5/3.3 vout models: 40 / 25 ma typ. other models: 70 / 45 ma typ. input current at full load 1.8 vout models: 760 / 380 ma typ. (nominal input 24/48 vin) 2.5/3.3 vout models: 1030 / 510 ma typ. other models: 1500 / 750 ma typ. input voltage variation ( dv/dt ) 5 v/ms, max. (complies with ets 300 132 part. 4.4) start-up voltage / under voltage lockout 24 vin models: 10 vdc / 8 vdc (typ.) 48 vin models: 18 vdc / 16 vdc (typ.) surge voltage (100 msec. max.) 24 vin models: 50 v max. 48 vin models: 100 v max. conducted noise (input) en 55022 level a, fcc part 15, level a with external capacitor (see note 1) esd (input) en 61000-4-2, perf. criteria b fast transient (input) en 61000-4-4, perf. criteria a surge (input) en 61000-4-5, perf. criteria b output specifications voltage set accuracy 1 % output voltage adjustment 10 % regulation C input variation vin min. to vin max. 0.5 % max. C load variation 10 C 100 %: single output models: 0.5 % max. dual output models: 1.0 % max. C load cross variation 25 % / 100 % 5 % max. temperature coefficient 0.02 %/k ripple and noise (20 mhz bandwidth) : 75 mvpk-pk max. start up time (nominal vin and constant resistive load) 10 ms typ. transient response setting time (25% load step change) 300 s typ. short circuit protection indefinite (automatic recovery) over load protection 150 % of iout max typ. foldback thermal shutdown at +115c typ over voltage protection 1.8, 2.5 & 3.3 v output models: 3.9 v 5.0 v output models: 6.2 v 12 v output models: 15 v 15 v output models: 18 v minimum load (only for dual output models) 10% of rated max current (operation at lower load condition will not damage these converters, however, they may not meet all listed specifications) capacitive load 1.8 / 2.5 vout models: 65000 f max./ 33000 f max. 3.3 / 5.0 vout models: 19500 f max./ 10200 f max. 12 / 15 vout models: 3300 f max./ 1100 f max. 12 / 15 vout models: 1000 f max./ 680 f max. (per output) dc/dc converters ten 30wi 30 watt all specifcations valid at nominal input voltage, full load and +25c after warm-up time unless otherwise stated. page 2 of 4
http://www.tracopower.com dc/dc converters ten 30wi 30 watt general specifications temperature ranges C operating C40c to +85c C case temperature +100c max. C storage C55c to +105c thermal impedance C with heat-sink ten-hs2 8.24 k/watt C without heat-sink 10 k/watt derating www.tracopower.com/products/ten30wi-derating.pdf humidity (non condensing) 95 % rel h max. reliability, calculated mtbf (mil-hdbk-217f, at +25c, ground benign) >350000 h isolation voltage (60sec.) C input / output 1500 vdc isolation resistance C input / output >1000 m ohm isolation capacitance C input / output 1000 pf max. remote on/off C on: 3.5 ... 12 vdc or open circuit. C off: 0 ... 1.2 vdc or short circuit pin 3 and pin 2 C off idle current: 3 ma typ. switching frequency 300 khz typ. (pulse width modulation pwm) vibration 10C55 hz, 2g, 30 minutes along x,y,z safety standards ul 60950, iec/en 60950, compliance up to 60 vdc input voltage (selv limit) safety approvals C ul/cul www.ul.com > ul file no.: e188913 environmental compliance C reach www.tracopower.com/products/ten30wi-reach.pdf C rohs rohs directive 2002/95/ec output voltage adjustment rd trim +vout ru trim - vout trim up ru [kohm] * output 1.8v 2.5v 3.3v 5.0v +5% 1.2 4.3 6.8 4.7 +10% 0.068 0.82 1.5 0.56 output 12v 15v 12v 15v +5% 47 47 27 33 +10% 8.2 6.8 2.2 2.7 trim down ru [kohm] * output 1.8v 2.5v 3.3v 5.0v C5% 1.8 6.8 8.2 5.6 C10% 0.1 0.82 0.68 0.68 output 12v 15v 12v 15v C5% 56 56 33 39 C10% 5.6 2.2 2.7 3.3 all specifcations valid at nominal input voltage, full load and +25c after warm-up time unless otherwise stated. page 3 of 4 note 1 : in order to meet conducted emissions en55022-a and en55011-a a capacitor between +vin and -vin has to be installed. the capacitor should be capable to handle 1 a ripple current. a suggestion is kmf series of nippon chemi-con, 220f/100v, esr 90mohm. *approximate values
outline dimensions pin single dual 1 +vin (vcc) +vin (vcc) 2 Cvin (gnd) Cvin (gnd) 3 remote on/off 4 no pin +vout 5 +vout common 6 Cvout Cvout 7 trim pin-out re v. 0 4/12 physical specifications casing material copper, nickel plated baseplate material none conductive fr4 potting material epoxy (ul 94v-0 -rated) weight 48 g (1.69 oz ) soldering temperature max. 265c / 10 sec. heat-sink ten-hs2 56.0 (2.2) max. 23.0 (0.9) 17.2 (0.68) max. conver ter heat-sink thermal pad clamp 5.6 10.2 40.6 10.16 10.16 10.16 5.08 50.8 6 5 4 1 2 7 bottom view 45.72 (2.0) (0.22) (1.6) (0.4) (0.4) (0.4) (0.4) (0.2) (1.8) 12.7 (0.5) 5.1 (0.2) 3 10.16 (0.4) page 4 of 4 dc/dc converters ten 30wi 30 watt dimensions in [mm], () = inch pin diameter: 1.0 0.05 (0.02 0.002) pin pitch tolerances: 0.35 (0.014) case tolerances: 0.5 (0.02) note: the product label on converter has to be removed before mounting the heat-sink. for volume orders converters will be supplied with heat-sinks already mounted. please con - tact factory for quotation. separate heat-sinks are only available for prototypes and small quantity orders. order code: ten-hs2 (cont.: heat-sink, thermal pad, 2 clamps) material: aluminum finish: anodic treatment (black) weight: 19 g (0.67oz) (without converter) specifcations can be changed any time without notice. 3d step file: www.tracopower.com/products/ten30wi-3d.stp jenatschstrasse 1 ch-8002 zurich switzerland t el. +41 43 311 45 11 fax +41 43 311 45 45 info@traco.ch www .tracopower .com
|
